Battlebooze 3D for print
973 Views 0 Likes 0 Downloads Download
After gr3t3l showed an image of a crude version of battleship with booze, we jus...t had to do a proper version with ship models, thus BattleBooze was born.
The ships were designed in blender for shotglasses with a diameter of up to 35mm, though bigger ones might also fit.
We designed for a grid size of 8x8cm per shotglass, therefore the higher capacity models (>=destroyer/3 shots) might be to big for your standard 3D printer like the Ultimaker classic we used.
Each of these bigger ships was cut into puzzle pieces that should be printable on a smaller plattform.
For those feeling a little adventurous, we included the uncut models, so you can try to print them in whole on a makerbot replicator 2, for example.
--- For making it, just print out all the parts and put them together. They all print fine on an Ultimaker classic with normal quickprint settings and support enabled, though you might want to print the 5xCarrier upside down to save material. --
- 2 1xPatrolboat.stl
- 2 1xPatrolboat_frontCannon.stl
- 2 1xPatrolboat_frontCannon_barrel....stl
- 4 1xPatrolboat_launcher.stl
- 2 2xSubmarine.stl
- 2 3xDestroyer.stl
- 4 3xDestroyer_cannon.stl
- 2 4xBattleship_front.stl
- 2 4xBattleship_center.stl
- 2 4xBattleship_rear.stl
- 2 4xBattleship_radar.stl
- 6 4xBattleship_cannon.stl
- 18 4xBattleship_cannon_barrel.stl
- 16 4xBattleship_aux_cannon.stl
- 32 4xBattleship_aux_barrel.stl (you might want to merge the aux_cannons and aux_barrels with each other, or the main battleship.stl, if you want to avoid glueing the small parts together)
- 2 5xCarrier_front.stl
- 2 5xCarrier_center.stl
- 2 5xCarrier_rear.stl
- 2 5xCarrier_bridge.stl
Designer
Florian L.3d model description
Your favourite childhood game with a twist - if you sink, you drink.After gr3t3l showed an image of a crude version of battleship with booze, we jus...t had to do a proper version with ship models, thus BattleBooze was born.
The ships were designed in blender for shotglasses with a diameter of up to 35mm, though bigger ones might also fit.
We designed for a grid size of 8x8cm per shotglass, therefore the higher capacity models (>=destroyer/3 shots) might be to big for your standard 3D printer like the Ultimaker classic we used.
Each of these bigger ships was cut into puzzle pieces that should be printable on a smaller plattform.
For those feeling a little adventurous, we included the uncut models, so you can try to print them in whole on a makerbot replicator 2, for example.
--- For making it, just print out all the parts and put them together. They all print fine on an Ultimaker classic with normal quickprint settings and support enabled, though you might want to print the 5xCarrier upside down to save material. --
3d model print parameters
For a complete BattleBooze set, you will need to print...- 2 1xPatrolboat.stl
- 2 1xPatrolboat_frontCannon.stl
- 2 1xPatrolboat_frontCannon_barrel....stl
- 4 1xPatrolboat_launcher.stl
- 2 2xSubmarine.stl
- 2 3xDestroyer.stl
- 4 3xDestroyer_cannon.stl
- 2 4xBattleship_front.stl
- 2 4xBattleship_center.stl
- 2 4xBattleship_rear.stl
- 2 4xBattleship_radar.stl
- 6 4xBattleship_cannon.stl
- 18 4xBattleship_cannon_barrel.stl
- 16 4xBattleship_aux_cannon.stl
- 32 4xBattleship_aux_barrel.stl (you might want to merge the aux_cannons and aux_barrels with each other, or the main battleship.stl, if you want to avoid glueing the small parts together)
- 2 5xCarrier_front.stl
- 2 5xCarrier_center.stl
- 2 5xCarrier_rear.stl
- 2 5xCarrier_bridge.stl
