Openr/c 1:10 formula 1 car 3D for print
3381 Views 2 Likes 0 Downloads Download the piece here from 3dforprint
Please respect the license under which this project is released. Thank you!
This is the OpenR/C Formula 1 car. It´s ...the third generation OpenR/C car and this time around focus is on simplicity! You can print everything in PLA except the tires which are done in NinjaFlex! Of course you can print it in any material you like but for those that want to print a car but only have PLA at hand, this is the project for you!
A note on the servo saver. It´s designed to be used with PLA, the upper and lower BOM applies force similar to a spring in a convetional servo saver. Of course the pressure depends on the type of material used, infill etc. Fine tuning can be done adding washer under or over the servo saver.
The "Main Turning Vane´s" needs to have it´s lower part trimmed using a "exacto knife". Then slide it in the chassie plate and push it over the "Lid" and it should snap into place-
Complete hardware/electronics kit is available here: http://www.3dprintnpack.com/product-page/4054b44d-0bfb-cfed-4661-451da35810da
Parts that need support added:
Front Spoiler.stl
Front.stl
Rear Rim.stl
Rear Wing.stl
Servo Saver Lower.stl
Things to buy:
Ok, obviously you need some filament which you´ll get from your favourite filament supplier.
You also need M3 screws and nuts which you can get at your local hardware store. Check the BOM list for what to get.
Some bearings are needed aswell, check the BOM list or buy a kit from FastEddyBearings.com:http://www.fasteddybearings.com/openrc-f1-sealed-bearing-kit/
Last but not least you need electronics and here´s what i got, all from HobbyKing:
ESC and motor combo:http://www.hobbyking.com/hobbyking/store/__65982__TrackStar_ROAR_approved_1_10th_Stock_Class_Brushless_ESC_and_Motor_Combo_21_5T_.html
Battery:http://hobbyking.com/hobbyking/store/__23134__Turnigy_nano_tech_Shorty_4200mah_2S2P_65_130C_Hardcase_Lipo_Pack_ROAR_APPROVED_.html
Micro Servo This is what i bought and i think it´s not very good, please let me know if you have a better revommendation.http://www.hobbyking.com/hobbyking/store/__7472__Turnigy_8482_TGY_1800A_Servo_1_5kg_0_10sec_8g.html
Transmitter and Receiver (i use something else but this is a "cheap" alternative):http://hobbyking.com/hobbyking/store/__83360__HobbyKing_174_8482_HK_GT2B_3CH_2_4GHz_Transmitter_and_Receiver_w_Rechargable_Li_ion_Battery.html
If you are new to this whole R/C hobby you´ll also need a LiPo charger for the battery. Ask in the Google + Community for recommendations:https://plus.google.com/u/0/communities/112745535856143176146
Rain tires designed by Thomas Palm are available here:http://www.thingiverse.com/thing:999257
Low profile rims & tires designed by Thomas Palm are available here:http://www.thingiverse.com/thing:1103751
Designer
Daniel Norée3d model description
Third 3Dprinted Open R/C carPlease respect the license under which this project is released. Thank you!
This is the OpenR/C Formula 1 car. It´s ...the third generation OpenR/C car and this time around focus is on simplicity! You can print everything in PLA except the tires which are done in NinjaFlex! Of course you can print it in any material you like but for those that want to print a car but only have PLA at hand, this is the project for you!
A note on the servo saver. It´s designed to be used with PLA, the upper and lower BOM applies force similar to a spring in a convetional servo saver. Of course the pressure depends on the type of material used, infill etc. Fine tuning can be done adding washer under or over the servo saver.
The "Main Turning Vane´s" needs to have it´s lower part trimmed using a "exacto knife". Then slide it in the chassie plate and push it over the "Lid" and it should snap into place-
Complete hardware/electronics kit is available here: http://www.3dprintnpack.com/product-page/4054b44d-0bfb-cfed-4661-451da35810da
Parts that need support added:
Front Spoiler.stl
Front.stl
Rear Rim.stl
Rear Wing.stl
Servo Saver Lower.stl
Things to buy:
Ok, obviously you need some filament which you´ll get from your favourite filament supplier.
You also need M3 screws and nuts which you can get at your local hardware store. Check the BOM list for what to get.
Some bearings are needed aswell, check the BOM list or buy a kit from FastEddyBearings.com:http://www.fasteddybearings.com/openrc-f1-sealed-bearing-kit/
Last but not least you need electronics and here´s what i got, all from HobbyKing:
ESC and motor combo:http://www.hobbyking.com/hobbyking/store/__65982__TrackStar_ROAR_approved_1_10th_Stock_Class_Brushless_ESC_and_Motor_Combo_21_5T_.html
Battery:http://hobbyking.com/hobbyking/store/__23134__Turnigy_nano_tech_Shorty_4200mah_2S2P_65_130C_Hardcase_Lipo_Pack_ROAR_APPROVED_.html
Micro Servo This is what i bought and i think it´s not very good, please let me know if you have a better revommendation.http://www.hobbyking.com/hobbyking/store/__7472__Turnigy_8482_TGY_1800A_Servo_1_5kg_0_10sec_8g.html
Transmitter and Receiver (i use something else but this is a "cheap" alternative):http://hobbyking.com/hobbyking/store/__83360__HobbyKing_174_8482_HK_GT2B_3CH_2_4GHz_Transmitter_and_Receiver_w_Rechargable_Li_ion_Battery.html
If you are new to this whole R/C hobby you´ll also need a LiPo charger for the battery. Ask in the Google + Community for recommendations:https://plus.google.com/u/0/communities/112745535856143176146
Rain tires designed by Thomas Palm are available here:http://www.thingiverse.com/thing:999257
Low profile rims & tires designed by Thomas Palm are available here:http://www.thingiverse.com/thing:1103751
