3DFORPRINT
Image to STL converter
3D models on demand
English
Español
Sign up
Log in
Micro c-130 hercules rc model 3D for print
UNLIKE
LIKE
×
Close
3575 Views
2 Likes
3 Downloads
Download
Designer
TAHUSTVEDT
3d model description
EDIT - 15.03.2020:
Added new wing parts that can be printed completely with vase mode for better print quality and easier printing with LW-PLA. Also
...
added Aileron02 and Elevator02 which print in one piece for vase mode, and need to be separated after printing.
Wingspan: 610 mm
Length: 433 mm
AUW: 100-115 g
CG: ~20mm from the leading edge of the wing center section.
For experienced users. It requires basic modeling skills to set up the control surfaces and build the plane. I have not flown the plane under power yet, but I have flown it freeflight with ballast and AUW 109 g. It flies well.
Print settings:
Mine were all printed on normal printers witnh normal PLA and 0,4 mm nozzles. You can print thinner than 0,4 mm perimeters just fine with a 0,4 mm nozzle.
Print most parts with one 0,25 mm perimeter and 0,12 mm layer height. Use two bottom layers and four top layers for most parts. Add top layers as necessary to fill the top.
Print Fuselage02 with 0 top layers. Fuselage01 will go into the open end of Fuselage02.
Cut away the bottom layers after printing to lighten the model, as shown in the photo of the backside of the green part Fuselage01. as a reference, Fuselage01 should weigh ~6,5 g off the printer and ~5,5 g after trimming down the rear face. I use scissors like these to cut around the inside:
https://rover.ebay.com/rover/1/710-53481-19255-0/1?ff3=4&toolid=11800&pub=5575353675&campid=5338226872&mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fitm%2FCurved-Lexan-Scissors-RC-Car-Bodyshell-Cutting-For-Polycarbonate-Shells-Arches-%2F371079169069
Hinge elevators with Blenderm on the top surface.
Hinge ailerons with Blenderm on the bottom surface.
Hinge the rudder with tiny pieces of CA hinge.
Use 0,8 mm piano wire to connect the elevators together.
Use 0,8 mm piano wire to greate a torque link to the rudder.
Use 0,8 mm piano wire to create torque links to the ailerons in the slots in the bottom of the wing.
Required hardware:
1 mm carbon rods. 2 mm carbon rods
3 mm carbon rods. 0,8 mm piano wire
CA glue. CA hinge
Blenderm hinge tape
Can be used with 8,5 mm coreless motors or tiny outrunners.
https://hobbyking.com/en_us/turnigy-d0703-10000kv-brushless-motor.html?affiliate_code=BSFWYBUNYWDKXJN&_asc=5338582182
Suggested electronics:
Receiver and rudder/elevator servo:
https://www.banggood.com/custlink/33K3dSpugG
Aileron servo:
https://www.banggood.com/custlink/vGDmdSrueL
450 mAh 1S lipo.
Motors:
https://hobbyking.com/en_us/turnigy-d0703-10000kv-brushless-motor.html?affiliate_code=BSFWYBUNYWDKXJN&_asc=3215844319
ESCs:
https://hobbyking.com/en_us/yep-7a-1-2s-brushless-speed-controller.html?affiliate_code=BSFWYBUNYWDKXJN&_asc=2672935468
Read more
Tags
Ultra
Micro
C-130
Hercules
Model
Scale
Rc
Plane
License
CC Attribution-NonCommercial
Related 3d models with tags
Hercules Fight Achelous Metamorphosed into a Snake at The Louvre, Paris
Micro Snowflakes - from the Snowflake Machine
SD Card & micro SD Card Box with USB Stick Holder
Motorized Star Wars AT-AT
Micro drip irrigation nozzle
Ultralight PET Timelapse Motion Control Dolly
Micro Chess set
Memory Card Holder
Micro chain ring
N-Scale Distribution Center (1:160)
18650 Powerbank
Tesla Model S - Key Chain
Tesla Model X - Key Chain
X-Wing Kit Card REDUX
Cessna 172 Kit Card
DH.98 Mosquito Kit Card
SpaceShipTwo Kit Card
Nativity Scene Kit Card
Cessna 206 Celling tethered airplane toy
N-scale Track Bumper (1:160)
AT-ST Kit Card
Eurofighter Typhoon Kit Card
Boon the Tiny T. Rex: Allosaurus UpKit (Arms ONLY) - 3DKitbash.com
X-15 Kit Card
×
Login
Incorrect username or password, please review the data.
You must validate your email before you can enter
Forward validation email.
Login
Have you forgotten your password?
Reset password
Reset password
×
Email
Thanks for signing up 3dforprint
×
We just sent you a message with an activation link. If you haven't received it within 10 minutes, check your spam folder.
An email has been sent to your email account with instructions to reset the password.
We just sent you a message with an activation link. If you haven't received it within 10 minutes, check your spam folder.
×
Sign up
Create your 3dforprint account